Blume Mechanical ServiceBlumeMechanical Service

HVAC, explained

Caulk and seal air leaks in your home

Air that leaks through a home's outer walls, windows, doors and other openings wastes energy and raises utility costs (ENERGY STAR). ENERGY STAR describes DIY checks for finding leaks, such as a flashlight test and a smoke test (ENERGY STAR). Use caulk for gaps of a quarter inch or less and expanding spray foam for larger gaps (ENERGY STAR).

Caulk and foam are the materials ENERGY STAR names for sealing, but the gap has to be found before it can be sealed. This page explains the DIY checks ENERGY STAR describes, the materials it names for each gap size, and where those materials are used in attics, basements and around flues. The order of the sections follows the DIY checks first, then the sealing materials. Each section stands on its own, so you can skip ahead to the material you need.

Why air leaks cost energy

Air that leaks through a home's outer walls, windows, doors and other openings wastes energy and raises utility costs (ENERGY STAR).

Sealing air leaks and adding insulation are two of the most cost-effective ways to improve energy efficiency and comfort in a home (ENERGY STAR).

Most homes in the United States have significant air leaks and not enough insulation (ENERGY STAR). The steps below are for finding those leaks in your own home first.

Start with a visual check

Start by conducting a visual air leakage inspection on your home to look for cracks and gaps at the common leak sites (ENERGY STAR).

Take note of where you see gaps so you can come back and seal them later (ENERGY STAR).

Check for gaps in the attic that facilitate air movement by checking for dirty insulation (ENERGY STAR).

Place each spot on a written list as you go, so none are missed when you start sealing.

Test with a flashlight at night

Shine a flashlight at night over all potential gaps while a partner observes the house from outside (ENERGY STAR).

Where you see light shine through, that spot has an air leak (ENERGY STAR).

While lights are on in the home, observe from the attic, crawlspace or basement any light from the interior of the house shining through gaps and cracks (ENERGY STAR).

Use incense, talc or a damp hand

The DIY smoke test is done by turning on all fans and vents and using incense smoke, talcum powder or baby power to find potential leak sites (ENERGY STAR).

Wherever the smoke wavers, or is sucked out of or blown into the room, there's a leak (ENERGY STAR).

You can also use a damp hand to locate leaks, because any leaks will feel cool to your hand (ENERGY STAR).

If you want a full check, consider hiring a home energy professional to perform a comprehensive energy audit (ENERGY STAR).

Pick caulk or foam by gap size

Silicone or acrylic latex caulk is used for sealing small holes of a quarter inch or less (ENERGY STAR).

Several cans of expanding spray foam insulation are used for filling larger gaps, from a quarter inch to three inches (ENERGY STAR).

Use caulk for any gaps or cracks of a quarter inch or less, and spray foam for anything larger (ENERGY STAR).

Seal attic openings around pipes, wires and boxes

Use expanding foam or caulk to seal the openings around plumbing vent pipes and electrical wires (ENERGY STAR).

Caulk around electrical junction boxes, and fill holes in boxes with caulk (ENERGY STAR).

Fill wiring and plumbing holes with expanding foam (ENERGY STAR).

If the space around a plumbing pipe is wider than 3 inches, you may need to stuff some fiberglass insulation into the space to serve as a backer for the expanding foam (ENERGY STAR).

When the foam or caulk is dry, cover the area again with insulation (ENERGY STAR).

Seal basement and crawlspace gaps

Seal any gaps or cracks in basement wall, ceiling or floor (ENERGY STAR).

Use caulk for gaps or cracks of a quarter inch or less in the basement, and spray foam for larger ones (ENERGY STAR).

Keep the list with your notes, so each spot can be checked again after sealing.

Flues, safety and when to call a professional

Special high-temperature caulk is used to seal around flues and chimneys (ENERGY STAR).

These gaps should be sealed with lightweight aluminum flashing and special high-temperature caulk (ENERGY STAR).

Be sure to wear gloves and be careful not to get expanding foam on your clothes, as the foam is very sticky and can be hard to remove once it sets (ENERGY STAR).

For a complete check of hidden leaks and safety issues, a home energy professional can help (ENERGY STAR).

Frequently asked

Where should I look for air leaks first?

ENERGY STAR says to start with a visual air leakage inspection of the common leak sites (ENERGY STAR). Take note of gaps so you can seal them later (ENERGY STAR).

Is caulk enough for every gap?

Silicone or acrylic latex caulk is used for small holes of a quarter inch or less (ENERGY STAR). Expanding spray foam is used for larger gaps, from a quarter inch to three inches (ENERGY STAR).

How does a flashlight test find a leak?

Shine a flashlight at night over all potential gaps while a partner observes the house from outside (ENERGY STAR). Where you see light shine through, that spot has an air leak (ENERGY STAR).

Can I use a damp hand to check for leaks?

ENERGY STAR says you can use a damp hand to locate leaks, because any leaks will feel cool to your hand (ENERGY STAR).

What caution applies to expanding foam?

ENERGY STAR advises wearing gloves and keeping expanding foam off your clothes, because it is very sticky and hard to remove once it sets (ENERGY STAR).

What material goes around a flue?

Special high-temperature caulk is used to seal around flues and chimneys (ENERGY STAR). Lightweight aluminum flashing is also named for those gaps (ENERGY STAR).

Related

Want a second look at the air conditioner while you check the house? Blume Mechanical Service (license CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment in Pinellas, Hillsborough and Pasco counties. Call 727-330-9131.

Sources: ENERGY STAR (U.S. EPA and DOE) — Why Seal and Insulate? (https://www.energystar.gov/saveathome/seal_insulate/why-seal-and-insulate) · ENERGY STAR (U.S. EPA and DOE) — What to Look For: DIY Checks and Inspections (https://www.energystar.gov/saveathome/seal_insulate/identify-problems-you-want-fix/diy-checks-inspections) · ENERGY STAR (U.S. EPA and DOE) — Attic Air Sealing Project (https://www.energystar.gov/saveathome/seal_insulate/attic-air-sealing-project) · ENERGY STAR (U.S. EPA and DOE) — Basement & Crawlspace Air Sealing and Insulating Project (https://www.energystar.gov/saveathome/seal_insulate/basement_crawlspace)

Search Google for caulking air leaks