HVAC, explained
Recessed lights, flues and soffits in the attic
Keep all insulation at least 3 inches away from recessed can lights, unless they are rated IC (ENERGY STAR). Insulation contacting recessed can lights can cause fire hazards (ENERGY STAR). Open stud cavities at dropped soffits can be huge sources of air leaks (ENERGY STAR).
The attic is where air leaks and insulation meet, and recessed lights, flues and soffits sit in the middle of that work. This page explains what ENERGY STAR says about finding leaks at those spots, sealing them, and keeping insulation away from fixtures that are not rated for contact. The sections follow the order most people use in the attic, from the big openings to the small fixtures.
Why the attic matters for air leaks
The attic is usually where you can find some of the largest opportunities to save energy in your home (ENERGY STAR). By air sealing in your attic, you can stop many major air leaks and help to maintain the desired temperature throughout your home (ENERGY STAR).
Air sealing the attic is generally a challenging DIY project, but the benefits can be substantial (ENERGY STAR). Combined with attic insulation, air sealing can help alleviate the formation of dangerous ice dams in the winter in cold-climate homes (ENERGY STAR).
EPA recommends air sealing the attic before adding attic insulation (ENERGY STAR). Adding insulation to the attic is generally a moderately difficult do-it-yourself project, but the benefits can be substantial (ENERGY STAR).
Find the leaks at soffits and open cavities
Dropped soffits may be filled or covered with insulation and hard to see (ENERGY STAR). These areas may have open stud cavities leading directly into the attic and can be huge sources of air leaks (ENERGY STAR).
Look for common locations of attic air leaks (ENERGY STAR). Dropped soffits that are open to the attic are one of those locations (ENERGY STAR).
Look for dirty insulation, which is evidence that air is moving through it (ENERGY STAR). Do not worry about finding every small hole, since the page says the biggest savings come from plugging the large ones (ENERGY STAR).
Seal dropped soffits
After removing insulation from a dropped soffit, cut a length of reflective foil or other blocking material (rigid foam board works well) a few inches longer than the opening to be covered (ENERGY STAR).
Keep a note of which soffits you have finished, so none are missed.
Flues and chimneys: clearance and sealing
The opening around a furnace or water heater flue or chimney can be a major source of warm air moving into the attic (ENERGY STAR).
Because the pipe gets hot, building codes usually require 1 inch of clearance from metal flues (2 inches from masonry chimneys) to any combustible material, including insulation (ENERGY STAR).
Caution: Furnace flues can be very hot (ENERGY STAR). Cut aluminum flashing to fit around the flue (ENERGY STAR). Seal the gap between the flue and metal flashing with special high-temperature caulk (ENERGY STAR).
Recessed can lights and insulation
Keep all insulation at least 3 inches away from recessed can lights, unless they are rated IC (ENERGY STAR). Insulation contacting recessed can lights can cause fire hazards (ENERGY STAR).
Some recessed lights can be designed for insulation contact, or IC, in which case no barrier is needed (ENERGY STAR).
If you are using loose fill insulation, sheet metal or wire mesh makes barriers around the openings for recessed lights (ENERGY STAR). Never lay insulation over recessed light fixtures or soffit vents (ENERGY STAR).
Check every can light you find in the attic against this rule.
Check the fixture before you insulate
Check the fixture first for the IC designation before installing insulation (ENERGY STAR).
Adding more insulation does not require the same type as the insulation already in the attic (ENERGY STAR). Layer rolls of fiberglass insulation perpendicular to the joists (ENERGY STAR). When laying down additional insulation, work from the perimeter toward the attic opening (ENERGY STAR).
Safety before you start
Sealing your home may trap indoor air pollutants such as carbon monoxide, radon and volatile organic compounds (VOCs) and create unsafe conditions (ENERGY STAR). To address this may require additional mechanical ventilation to maintain safe air quality in your home (ENERGY STAR).
Some attics have vermiculite insulation, which may contain asbestos (ENERGY STAR). Knob and tube wiring from before 1930 can be a fire hazard when in contact with insulation (ENERGY STAR).
Rebates and the work ahead
Many local utilities may offer rebates for a professional home energy assessment and certain home air sealing and insulation projects (ENERGY STAR). Ask your utility what it offers before you start, and confirm any money questions with the IRS, your utility or a tax professional.
Frequently asked
Can insulation touch a recessed can light?
Keep all insulation at least 3 inches away from recessed can lights, unless they are rated IC (ENERGY STAR). Insulation contacting recessed can lights can cause fire hazards (ENERGY STAR).
What does IC mean on a recessed light?
IC stands for Insulated Ceiling (ENERGY STAR). Some recessed lights can be designed for insulation contact, in which case no barrier is needed (ENERGY STAR).
How close can a flue be to insulation?
Building codes usually require 1 inch of clearance from metal flues (2 inches from masonry chimneys) to any combustible material, including insulation (ENERGY STAR). Check your local code for your own installation.
Do I have to seal every small hole in the attic?
The page says not to worry about finding and sealing all the little holes in your attic, and that the biggest savings come from plugging the large ones (ENERGY STAR).
Can sealing an attic affect indoor air?
Sealing your home may trap indoor air pollutants such as carbon monoxide, radon and volatile organic compounds (VOCs) and create unsafe conditions (ENERGY STAR). Additional mechanical ventilation may be required (ENERGY STAR).
Can I put insulation right over a recessed light?
Never lay insulation over recessed light fixtures or soffit vents (ENERGY STAR). Only recessed lights designed for insulation contact, marked IC, need no barrier (ENERGY STAR).
Related
- Air sealing the attic before adding insulation
- Home performance assessment and what it checks
- Attic insulation R-value: how to check your attic
Need an HVAC check for the air conditioner or furnace that serves your home? Blume Mechanical Service (license CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment in Pinellas, Hillsborough and Pasco counties. Call 727-330-9131.
Sources: ENERGY STAR (U.S. EPA and DOE) — Attic Air Sealing Project (https://www.energystar.gov/saveathome/seal_insulate/attic-air-sealing-project) · ENERGY STAR (U.S. EPA and DOE) — Attic Insulation Project (https://www.energystar.gov/saveathome/seal_insulate/attic-insulation-project) · Internal Revenue Service — Home energy tax credits (https://www.irs.gov/credits-deductions/home-energy-tax-credits)