Blume Mechanical ServiceBlumeMechanical Service

HVAC, explained

Attic insulation R-value: how to check your attic

ENERGY STAR recommends insulating most attics to R-38, or about 10 to 14 inches, depending on insulation type (ENERGY STAR). For a rough estimate, multiply the insulation depth in inches by 3 (ENERGY STAR). If the insulation is level with or below the floor joists, ENERGY STAR says you should add more (ENERGY STAR).

Start by measuring the insulation, then compare the reading with the figures below. Some figures come from University of Florida and Florida Solar Energy Center pages, and the rest come from ENERGY STAR's general guidance, so each figure names its source.

Measure the insulation depth

UF/IFAS says to measure the thickness of the insulation to find out whether you have enough (UF/IFAS). The R-value depends on both the type and the thickness of the material (UF/IFAS). Thickness and type both affect how much heat enters your home (UF/IFAS).

Measure at several spots across the attic, not only near the hatch, and write each reading down with its location.

Check whether the insulation reaches the joists

ENERGY STAR says that if your insulation is level with or below the floor joists, you should add more (ENERGY STAR). ENERGY STAR describes that level as the point where you can easily see the joists (ENERGY STAR). A visual check gives no R-value (ENERGY STAR), so treat it as a first step rather than a measurement.

Estimate the R-value from the depth

ENERGY STAR gives a rough method: multiply the insulation depth in inches by 3 (ENERGY STAR). The page calls the result an estimated value (ENERGY STAR).

Compare the estimate with the product label on the material you plan to add before you decide what to do.

Know the target for most attics

ENERGY STAR recommends R-38 for most attics, which is about 10 to 14 inches depending on insulation type (ENERGY STAR). That target is general guidance, not a Florida-specific or climate-zone-specific target (ENERGY STAR).

ENERGY STAR's retrofit table is based on the 2021 International Energy Conservation Code residential provisions (ENERGY STAR). That guidance applies to retrofitting existing wood-framed buildings (ENERGY STAR).

Florida sources on R-value and thickness

UF/IFAS points homeowners to the ZIP-Code Insulation Program for the recommended R-value in their area (UF/IFAS). UF/IFAS also says that an attic with less than 6 to 7 inches of insulation (R-22) could benefit from adding more (UF/IFAS). That figure is a threshold, not a code minimum (UF/IFAS).

FSEC advises choosing improvements that reduce both heat gain and heat loss, such as enhanced ceiling insulation (FSEC). That advice gives no R-value and does not rank ceiling insulation against other measures (FSEC).

The ENERGY STAR and UF/IFAS figures come from different sources, so check each one against your product label and a licensed contractor.

Match the new material to your target

ENERGY STAR says you do not have to use the same type of insulation that already exists in your attic when you add more (ENERGY STAR). The R-value depends on both the type and the thickness of the material you choose (UF/IFAS).

Compare the product label with your target before you buy.

Seal the attic floor before adding insulation

ENERGY STAR says contractors should seal air leaks in the attic floor before adding insulation (ENERGY STAR). It also says it is much easier to seal first, so you get the full performance out of your insulation (ENERGY STAR).

If you plan to add insulation yourself, read the sealing steps before you open a bag of material.

When to ask a licensed contractor

Ask a licensed contractor to confirm the depth, the R-value and the sealing work before you add material. Ask for the measurements and product labels in writing, and compare them with any written estimate you receive.

Frequently asked

How many inches of attic insulation do I need?

ENERGY STAR recommends R-38 for most attics, which is about 10 to 14 inches depending on insulation type (ENERGY STAR). Measure your depth and read the product label to match the material to that target. A licensed contractor can confirm the number for your attic.

How do I estimate the R-value of my attic insulation?

ENERGY STAR says to multiply the insulation depth in inches by 3 for an estimated value (ENERGY STAR). It is an estimate, so compare it with the product label before you decide.

Does insulation level with the floor joists mean I need more?

ENERGY STAR says you should add more if insulation is level with or below the floor joists (ENERGY STAR). A visual check gives no R-value (ENERGY STAR), so it is a first step.

Do I have to use the same insulation type that is already in my attic?

No. ENERGY STAR says you do not have to use the same type of insulation that currently exists in your attic when you add more (ENERGY STAR). The R-value depends on both type and thickness, so match the new material to your target (UF/IFAS).

Should the attic floor be sealed before I add insulation?

ENERGY STAR says contractors should seal air leaks in the attic floor before adding insulation (ENERGY STAR). It also says sealing first is much easier, so the insulation gets its full performance (ENERGY STAR).

Where can I find the recommended R-value for my area?

UF/IFAS points homeowners to the ZIP-Code Insulation Program for the recommended R-value in their area (UF/IFAS). Confirm that figure for your home with a licensed contractor before you order material.

Related

Need HVAC service? Blume Mechanical Service (CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment in Pinellas, Hillsborough and Pasco counties. Call 727-330-9131.

Sources: ENERGY STAR (U.S. EPA and DOE) — Adding Attic Insulation (https://www.energystar.gov/saveathome/seal_insulate/do-it-yourself-guide/adding-attic-insulation) · ENERGY STAR (U.S. EPA and DOE) — Well-Insulated and Sealed Attic (https://www.energystar.gov/products/energy_star_home_upgrade/attic_insulation) · ENERGY STAR (U.S. EPA and DOE) — Recommended Home Insulation R–Values (https://www.energystar.gov/saveathome/seal_insulate/identify-problems-you-want-fix/diy-checks-inspections/insulation-r-values) · UF/IFAS Living Green (University of Florida) — Insulation (https://livinggreen.ifas.ufl.edu/topics/energy/insulation/) · Florida Solar Energy Center (University of Central Florida) — How to Reduce Energy Costs in Existing Homes - Priorities (https://energyresearch.ucf.edu/consumer/buildings/priorities/)

Search Google for attic insulation r-value florida