Blume Mechanical ServiceBlumeMechanical Service

HVAC, explained

How to Use a Thermostat

On the Honeywell FocusPRO P200, each press of the MODE button moves to the next available system mode, and the FAN button moves to the next fan mode (Honeywell). On Lennox CS5500 touchscreen thermostats, one operating mode screen lists heat/cool, heat only, cool only, off and up to three schedules, and it also sets the fan to on, auto or circulate (Lennox).

Honeywell says the available modes depend on the model and system settings (Honeywell). Honeywell also says available fan modes vary with system settings (Honeywell).

Mode: choosing heat, cool or off

On the Honeywell FocusPRO P200, each press of the MODE button moves to the next available system mode (Honeywell). Honeywell's support article says that in Auto Changeover mode the display shows auto heat or auto cool beside the room temperature (Honeywell). On Lennox, press OPERATING MODE on the home screen to open the list of modes (Lennox). Lennox says heat/cool switches between heating and cooling on its own (Lennox), heat only allows only heating demand (Lennox), cool only allows only cooling demand (Lennox), and off means the system has been turned off (Lennox).

Fan: auto, on or circulate

On the Honeywell FocusPRO P200, the FAN button moves to the next available fan mode (Honeywell). Honeywell says AUTO runs the fan only while heating or cooling is on, ON keeps the fan running at all times, and CIRC runs the fan part of the time to circulate air (Honeywell). On Lennox, the fan is set by pressing ON, AUTO or CIRCULATE, and a green check mark marks the choice (Lennox). Lennox says CIRCULATE cycles the fan for a set amount of active time per hour while the heating or cooling equipment is not running (Lennox). Lennox also says a fan mode picked on the select mode screen overrides any fan setting in a schedule (Lennox).

Set point: changing the target temperature

Honeywell's support article says that if the display shows auto heat or auto cool, the + or – button changes the set point it names (Honeywell). If you want to change the other set point, Honeywell says you must first switch the mode to cool or heat, change the set point with + or –, and then switch back to Auto Changeover (Honeywell). On Lennox, touching the heat-to or cool-to figure on the home screen opens a temperature setting detail screen (Lennox). Lennox says the temperature dial turns red when heating is active and blue when cooling is active (Lennox).

Schedules: setting times and days

Carrier says a programmable thermostat adjusts the temperature on its own, following a schedule you create (Carrier). Carrier lists 7-day programming, which gives every day its own heating and cooling plan (Carrier). It lists 5-2, with one plan for Monday through Friday and another for Saturday and Sunday, and 5-1-1, with separate weekday, Saturday and Sunday plans (Carrier). Carrier shows a typical daily schedule with four time blocks, at 6:00 AM, 8:00 AM, 5:30 PM and 10:30 PM (Carrier). Honeywell says the program periods are wake, leave, return and sleep, and each set point can be changed while you move through them (Honeywell). Lennox says up to three schedules can be set, and each can be renamed and edited (Lennox). Lennox says you can select individual days or groups of days when you set programming (Lennox), and that a specific schedule runs from the selection mode screen (Lennox). ENERGY STAR says to change batteries each year if the thermostat runs on them, and some units show when a change is due (ENERGY STAR).

Hold and override: changing a setting for a period

Lennox says Program Hold options let you override the program schedule by time (Lennox). Touching the heat-to or cool-to spot on the home screen puts the schedule on hold, and the override choices are one hour, two hours or permanent (Lennox). A 1 or 2 hour hold shows the time it ends, and pressing X exits it (Lennox). A permanent hold stays in place until you press X (Lennox). ENERGY STAR says to set the hold button when going away for a weekend or on vacation (ENERGY STAR). ENERGY STAR also says to avoid overriding pre-programmed settings, and says every override uses more energy (ENERGY STAR).

Status icons, lock and backlight

Lennox says the first press on the screen turns on the backlight (Lennox). Red flames mean the system is heating, blue flames mean cooling, and a snowflake signals that cooling is next (Lennox). Lennox says the waiting icon marks a compressor delay of 5 minutes by default, and that the delay is not adjustable (Lennox). Lennox says setting options can be unlocked, partially locked or locked, and that a locked setting needs a three digit code (Lennox).

Away setting and zones

Lennox says AWAY lets you set separate heating and cooling temperatures for when you are away from home (Lennox). ENERGY STAR says to use a programmable thermostat for each zone if a house has several heating and cooling zones (ENERGY STAR). ENERGY STAR says that with a manual thermostat, you can adjust the temperature each day before you leave and at bedtime (ENERGY STAR).

Frequently asked

Do I need to call a pro for this?

No. If you are changing mode, fan, set point, schedule or hold, you are using thermostat settings, which the Honeywell and Lennox manuals describe as buttons and screens on the thermostat (Honeywell; Lennox). If the system still does not respond after you check those settings, have a licensed contractor check the equipment.

What does auto heat or auto cool mean on the display?

Honeywell's support article says that in Auto Changeover mode, the label beside the room temperature reads auto heat or auto cool (Honeywell). The + and – buttons then change the set point named on the display (Honeywell).

Why does the fan run when heating and cooling are off?

Honeywell says AUTO runs the fan only when heating or cooling is on, while ON keeps it running (Honeywell). Lennox says CIRCULATE cycles the fan during equipment inactivity (Lennox), and ON runs the fan continuously until the setting is changed on the select mode screen (Lennox).

How do I end a hold?

On Lennox, pressing X exits the hold (Lennox). A 1 or 2 hour hold also ends at the time shown on the home screen (Lennox), and a permanent hold stays in place until X is pressed (Lennox).

What does the waiting icon mean?

Lennox says the waiting icon marks a compressor delay, which is 5 minutes by default and is not adjustable (Lennox). Lennox also says a snowflake signals that cooling is next (Lennox).

Related

Questions about a specific system can go to Blume Mechanical Service at (727) 330-9131.

Sources: Honeywell Home, FocusPRO P200 Series Smart Thermostat User Manual, Operation Settings (models TH2110U4004, TH2320U4006), https://docs.honeywellhome.com/focuspro-p200-um/en-us/Content/User-Manual/Operation%20Settings.htm · Honeywell Home, Auto Changeover Mode On Your Thermostat (support article, last updated September 2, 2025), https://www.honeywellhome.com/blogs/support/what-is-auto-changeover · Lennox, CS5500 Color Touchscreen Programmable Thermostat User Guide (model 13H13), https://www.lennox.com/lib/legacy-res/pdfs/manuals/cs5500_userguide.pdf · ENERGY STAR, A Guide to Energy-Efficient Heating and Cooling, https://www.energystar.gov/ia/partners/publications/pubdocs/HeatingCoolingGuide%20FINAL_9-4-09.pdf · Carrier, Programmable Thermostats, https://www.carrier.com/us/en/residential/hvac-resources/smart-thermostats/programmable-thermostat/

Search Google for how to use a thermostat