Blume Mechanical ServiceBlumeMechanical Service

HVAC, explained

Wall insulation for existing homes: options and limits

When exterior siding is removed, ENERGY STAR says to drill holes and blow insulation into an uninsulated wood-frame wall before the new siding goes on (ENERGY STAR). ENERGY STAR lists blown-in products as suited for enclosed existing walls (ENERGY STAR). Sealing air leaks and adding insulation are two of the most cost-effective ways to improve efficiency (ENERGY STAR).

Heat can be lost or gained through gaps where walls, ducts, pipes and vents meet (U.S. Department of Energy). Existing walls can be insulated in a few ways, and the right method depends on the wall and on whether the siding is already being replaced. The points below come from federal and ENERGY STAR guidance, and each names its source.

Insulating walls when the siding is off

When exterior siding is removed, ENERGY STAR describes drilling holes and blowing insulation into an uninsulated wood-frame wall before the new siding goes on (ENERGY STAR). The same page says to add insulative sheathing under the new siding (ENERGY STAR).

For Zone 3, the page says to add R5 insulative wall sheathing beneath new siding (ENERGY STAR). For Zones 4 to 8, the page says to add R5 to R10 insulative wall sheathing beneath new siding (ENERGY STAR).

For insulated 2x4 wood-frame walls in Zones 4 to 8, the page says to add R10 insulative wall sheathing beneath new siding (ENERGY STAR). The page states that this guidance is based on the 2021 International Energy Conservation Code (ENERGY STAR).

Find the zone that applies to your home before you use any of these figures, since the figures differ by zone.

Exterior insulation and payback

Adding continuous exterior insulation of at least 1 inch is only incrementally more expensive than the siding, when the siding is already being replaced (U.S. Department of Energy). The payback of exterior insulation is longer than caulking and weatherstripping, often between 5 and 10 years (U.S. Department of Energy).

The same DOE page says the comfort and noise improvements from this upgrade are immediately noticeable (U.S. Department of Energy).

Get a written estimate that shows the cost of the insulation and the siding separately, so you can see the added cost on its own.

Blown-in insulation for enclosed walls

ENERGY STAR's product chart lists blown-in products as suited for enclosed existing walls (ENERGY STAR).

Insulation performance is highly dependent on the quality of the installation (ENERGY STAR). Ask the installer how the drilled holes will be filled and sealed afterward, and ask for the product name in writing.

Compare more than one estimate, and read each one against the same list of questions.

Basement and crawl space walls

For basement or crawl space walls in Zones 4A and 4B, the page says to add R10 insulative sheathing or R13 batt (ENERGY STAR). For basement or crawl space walls in Zones 4C and 5 to 8, the page says to add R15 insulative sheathing or R19 batt (ENERGY STAR).

The page states these figures for basement or crawl space walls (ENERGY STAR). Find your zone and wall type before you use these figures.

Sealing air leaks alongside insulation

Sealing air leaks and adding insulation are two of the most cost-effective ways to improve energy efficiency and comfort in your home (ENERGY STAR). A well-sealed envelope, coupled with the right amount of insulation, can make a real difference on your utility bills (ENERGY STAR).

Most homes in the United States do not have enough insulation and have significant air leaks (ENERGY STAR). Heat can be lost or gained through gaps where different parts of the building meet, such as walls, ducts, pipes and vents (U.S. Department of Energy).

Ask the contractor what air sealing is planned alongside the insulation, and get that step written into the estimate.

Certified products and testing

ENERGY STAR certified insulation must also be tested to meet flame resistance requirements to help promote fire safety (ENERGY STAR). The ENERGY STAR program only partners with insulation manufacturers who agree to have their products tested by a third-party certification body (ENERGY STAR).

Ask whether the product is ENERGY STAR certified before you accept the estimate.

Questions to ask before work starts

Ask which wall type the installer has assessed, and whether the siding will be removed or only the interior finished. Ask which product will be used and what R-value it provides.

Ask how the work will be checked after it is finished. Keep each answer with the written estimate so the work can be compared later. Write down the answer to each question, then compare estimates on the same points.

Frequently asked

Can existing walls be insulated without removing the siding?

ENERGY STAR describes drilling holes and blowing insulation into an uninsulated wood-frame wall when the new siding goes on (ENERGY STAR).

What sheathing does ENERGY STAR suggest for Zone 3?

For Zone 3, the page says to add R5 insulative wall sheathing beneath new siding (ENERGY STAR). The figure applies to the wall when the siding is replaced.

Is blown-in insulation suited to existing walls?

ENERGY STAR's product chart lists blown-in products as suited for enclosed existing walls (ENERGY STAR). Ask the installer which product is used and how the holes will be sealed.

Is exterior wall insulation worth the cost?

Adding continuous exterior insulation is only incrementally more expensive than the siding, when the siding is already being replaced (U.S. Department of Energy). The payback is longer than with caulking and weatherstripping, often between 5 and 10 years (U.S. Department of Energy).

Should walls be air sealed along with insulation?

Sealing air leaks and adding insulation are two of the most cost-effective ways to improve energy efficiency and comfort (ENERGY STAR). Ask the contractor what air sealing is planned alongside the insulation.

Does wall insulation need to be certified?

The ENERGY STAR program only partners with insulation manufacturers who agree to have their products tested by a third-party certification body (ENERGY STAR). ENERGY STAR certified insulation must also be tested to meet flame resistance requirements (ENERGY STAR).

Related

Need an HVAC check on the air conditioner in your home? Blume Mechanical Service (license CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment in Pinellas, Hillsborough and Pasco counties. Call 727-330-9131.

Sources: ENERGY STAR (U.S. EPA and DOE) — Recommended Home Insulation R-Values (https://www.energystar.gov/saveathome/seal_insulate/identify-problems-you-want-fix/diy-checks-inspections/insulation-r-values) · ENERGY STAR (U.S. EPA and DOE) — Well-Insulated and Sealed Attic (https://www.energystar.gov/products/energy_star_home_upgrade/attic_insulation) · ENERGY STAR (U.S. EPA and DOE) — Why Seal and Insulate? (https://www.energystar.gov/saveathome/seal_insulate/why-seal-and-insulate) · ENERGY STAR (U.S. EPA and DOE) — Choosing the Appropriate Insulation Type (https://www.energystar.gov/saveathome/seal_insulate/certified_insulation) · U.S. Department of Energy — Energy-Efficient Home Improvement Credit: Insulation and Air-Sealing Essentials (https://www.energy.gov/cmei/buildings/articles/energy-efficient-home-improvement-credit-insulation-and-air-sealing)

Search Google for wall insulation existing homes