HVAC, explained
Thermostat Wire Colors and Terminal Letters
The common thermostat terminal letters are R (24 VAC from the heating transformer), C (common), W (heat stage 1), Y (compressor stage 1 cooling), G (fan) and O/B (heat pump reversing valve), and each letter names the job of the wire on that terminal (Honeywell; Honeywell T6 Pro manual). Wire color is not a standard: Honeywell says “There is no standard for which color wire controls each function,” while Tulsa Welding School calls matching colors a common manufacturer practice and says the colors can vary (Honeywell; Tulsa Welding School).
According to Tulsa Welding School, the low-voltage wires that run from the thermostat to the cooling or heating equipment carry power to the components the thermostat switches. That system usually runs on 24 volts of alternating current from a control transformer (Tulsa Welding School).
The terminal letters and what each one does
Honeywell's consumer guide lists the role of each wire in a thermostat system (Honeywell). S is for indoor and outdoor wired sensors, Y for compressor stage 1 cooling, Y2 for compressor stage 2 cooling, G for the fan, C for common, and U for humidifier, dehumidifier or ventilator control (Honeywell). L/A is the input for a heat pump fault, O/B is the reversing valve on heat pump systems, E is emergency heat, Aux or W2 is heat stage 2, W is heat stage 1, R is 24 VAC from the heating transformer and Rc is 24 VAC from the cooling transformer (Honeywell). Honeywell's T6 Pro manual lists the same kinds of terminals for its own models: compressor contactor stage 1 and stage 2, changeover valve, auxiliary or heat stage 2, emergency heat, and heat stage 1 (Honeywell T6 Pro manual). Tulsa Welding School says always to rely on the manufacturer's wiring diagram for exact connections (Tulsa Welding School).
Why wire color cannot be relied on
Honeywell's consumer guide states that no standard assigns a color to each function (Honeywell). Tulsa Welding School describes matching colors as a common practice among manufacturers, in which the red wire goes to the R terminal and the yellow wire to the Y terminal (Tulsa Welding School). The same article notes that colors, terminal layouts and wire counts differ from system to system, and that finding wiring without the exact colors needed is not uncommon for technicians (Tulsa Welding School).
Wire count and signs of a mismatch
Honeywell says the most common setup is five wires, and that a system can have as few as two or as many as ten (Honeywell). If the terminals are labeled A, B and C or 1, 2 and 3, Honeywell says the system requires a communicating thermostat, so a new thermostat may not be directly compatible (Honeywell). If thick, black or red wires are present, Honeywell links them to line voltage systems, which need a line voltage thermostat rather than a low voltage model (Honeywell). Terminals labeled G1, G2 or G3 call for a thermostat that can control multiple fan speeds (Honeywell).
Heat pumps, dual-fuel systems and the R slider
Honeywell says a heat pump runs its compressor for both heating and cooling (Honeywell). Honeywell's note on trade model thermostats says they must work with dual-fuel setups: a heat pump covers the first one or two stages, and a gas or oil furnace handles backup or emergency heat (Honeywell).
Common wire and product requirements
Honeywell's T6 Pro manual says the common wire (C) is required for LA/A (Honeywell T6 Pro manual). Honeywell's FocusPRO P200 and S200 manual says S200 Smart models require a connection at the C terminal (Honeywell FocusPRO manual). Honeywell's guide says that on Trane models with an X or B wire, the thermostat manual is the reference, and that one of those wires can be the common (Honeywell).
Safety limits on thermostat wiring
Honeywell's FocusPRO manual says a trained, experienced HVAC professional must do the installation of this product (Honeywell FocusPRO manual). Its warning reads “IMPROPER WIRING OR CONFIGURING OF THIS THERMOSTAT CAN CAUSE UNINTENDED OPERATION OF YOUR HVAC SYSTEM WHICH COULD LEAD TO PROPERTY DAMAGE, INJURY, INCLUDING DEATH” (Honeywell FocusPRO manual). Tulsa Welding School advises turning off the circuit that powers the thermostat before anyone replaces the unit or handles its low-voltage wires, and Honeywell's FocusPRO manual says a trained, experienced HVAC professional must install the product (Tulsa Welding School; Honeywell FocusPRO manual).
Frequently asked
What do the R, C, W, Y and G terminals mean?
R is 24 VAC from the heating transformer, C is common, W is heat stage 1, Y is compressor stage 1 cooling, and G is the fan (Honeywell). Rc is 24 VAC from the cooling transformer (Honeywell).
Do wire colors always match the terminal letters?
No. Honeywell says there is no standard for which color controls each function (Honeywell). Tulsa Welding School describes matching colors as a common manufacturer practice, but says the colors, terminals and number of wires can vary (Tulsa Welding School).
What is the C wire?
C is the common terminal (Honeywell). The FocusPRO manual says S200 Smart models require a connection at C (Honeywell FocusPRO manual).
Do I need to call a pro for this?
Yes. For the wiring itself, hire a licensed contractor. Honeywell's FocusPRO manual says a trained, experienced HVAC professional must do the installation (Honeywell FocusPRO manual). Honeywell also says that with a dual-fuel system, or when unsure, you should stop and call a Professional HVAC Contractor (Honeywell). The checks you can make yourself are the air filter, the thermostat settings, keeping things away from the vents, returns and the outdoor unit.
What does Honeywell warn about improper thermostat wiring?
Honeywell's FocusPRO manual says improper wiring or configuring of the thermostat “can cause unintended operation of your HVAC system which could lead to property damage, injury, including death” (Honeywell FocusPRO manual).
Related
- The C-Wire on a Thermostat
- How a Thermostat Works
- What a furnace control board does and the signs it has failed
- Heat pump installation: what to expect and how to choose an installer
- What Hold Means on a Thermostat
Questions about a specific system can go to Blume Mechanical Service at (727) 330-9131.
Sources: Honeywell Home, How do I wire my thermostat? (last updated September 2, 2025), https://www.honeywellhome.com/blogs/support/how-do-i-wire-my-thermostat · Honeywell Home, T6 Pro Installation Manual, 2. Wiring, https://docs.honeywellhome.com/t6-pro-ii/en-us/Content/Installation-Instructions/2.%20Wiring.htm · Honeywell Home, FocusPRO P200 and S200 Series Installation Manual, Wiring Considerations, https://docs.honeywellhome.com/focuspro-p200-s200-im/en-us/Content/Installation-Manual/Wiring%20Considerations.htm · Tulsa Welding School, Introduction to Thermostat Wiring (archived blog), https://www.tws.edu/blog/hvac-r/introduction-to-thermostat-wiring/