Blume Mechanical ServiceBlumeMechanical Service

HVAC, explained

When an older building needs recommissioning

Recommissioning tests and adjusts building systems to meet their original design intent or current operational needs (DOE). It should be considered if systems are old, expensive to operate, and have frequent equipment failures (DOE). Good operations and maintenance practices can generate substantial energy and water savings (DOE).

This guide explains how the U.S. Department of Energy (DOE) describes commissioning, ongoing commissioning and recommissioning. It also covers the operations and maintenance practices that DOE links to energy and water losses. Each fact names its source, and the figures are general statements rather than promises for any one building.

What commissioning means

Commissioning is a quality-assurance process used to verify that a building performs according to the original design and intent and meets the needs of the owners and occupants (DOE). Federal agencies are required to make sure building systems and equipment are commissioned in new construction and existing buildings (DOE).

The DOE page on federal buildings sets out the process for federal owners. A facility manager at a private building can use the same definition to judge whether the systems still match the design.

Ongoing commissioning in existing buildings

Ongoing commissioning is designed to resolve operating problems, improve comfort, optimize energy use, and identify retrofits for existing buildings (DOE). Although it is ideal for large complex buildings with automation and advanced metering systems, ongoing commissioning is the most costly approach for existing buildings (DOE).

The process can identify equipment inefficiencies as they occur and allow for quick remediation and greater energy and cost savings (DOE). Compare the staffing needed for the process with the size and complexity of your building before you choose it.

What recommissioning is

In practice, recommissioning (ReCx) is accomplished through testing and adjusting the building systems to meet the original design intent or optimize systems to satisfy current operational needs (DOE). ReCx relies on building and equipment documentation, along with functional testing to optimize performance (DOE).

Keep the design documents, equipment submittals and past test reports in one file. Those records are the starting point for any testing that follows.

When recommissioning fits

ReCx is applied to buildings that have been previously commissioned, either as new or existing buildings (DOE). It is used in buildings that were previously commissioned to fine-tune them to meet their original design intents and operational efficiencies (DOE).

RCx is also used in older buildings that have never been through the commissioning process (DOE). Ask your engineer which of your systems were tested when the building was first built.

Why a newer building may need a review

ReCx should be considered for new buildings that were commissioned during construction and in which energy needs have increased (DOE). The process can identify and solve problems that occurred at construction but also addresses problems that have developed to this stage in the building's life (DOE).

While the goal of RCx may be to bring the building, its systems, and equipment back to its original design intent, that is not a requirement (DOE). Write down the target your building needs before any testing starts.

Signs that a building should be reviewed

RCx should be considered if building systems are old, expensive to operate, and have frequent equipment failures (DOE).

Track equipment failures and operating costs for a year, so you have data to bring to a review.

Why maintenance matters for energy

Effective operations and maintenance is one of the most cost-effective methods for ensuring reliability, safety, and energy and water efficiency (DOE). Inadequate maintenance of energy- and water-using systems is a major cause of waste in the federal government and the private sector (DOE).

Energy and water losses from steam, water and air leaks, uninsulated lines, maladjusted or inoperable controls, and poor maintenance and operations are often considerable (DOE). Good O&M practices can generate substantial energy and water savings (DOE).

Moreover, improvements to facility maintenance programs can often be accomplished immediately and at a relatively low cost (DOE). Start with a walk-through of leaks, insulation and controls before you schedule larger work.

Next steps for a facility manager

Write down the age of each major system, its operating cost and its failure history. Compare those records with the original design documents, and list the systems that no longer match them.

If the list points to heating or cooling equipment, a licensed technician can test and adjust it. Blume Mechanical Service repairs, installs and maintains HVAC and refrigeration equipment in Pinellas, Hillsborough and Pasco counties.

Frequently asked

What is recommissioning?

In practice, recommissioning is accomplished through testing and adjusting the building systems to meet the original design intent or current operational needs (DOE). It relies on building and equipment documentation and functional testing (DOE).

When should a building be recommissioned?

RCx should be considered if building systems are old, expensive to operate, and have frequent equipment failures (DOE). It can also be considered for new buildings whose energy needs have increased (DOE).

Does recommissioning have to restore the original design?

The goal may be to bring the building, its systems, and equipment back to its original design intent, but that is not a requirement (DOE). Recommissioning is applied to buildings that have been previously commissioned (DOE).

Is ongoing commissioning cheap?

Ongoing commissioning is the most costly approach for existing buildings, although it is ideal for large complex buildings with automation and advanced metering systems (DOE).

Can maintenance alone save energy?

Good O&M practices can generate substantial energy and water savings (DOE). Improvements to facility maintenance programs can often be accomplished immediately and at a relatively low cost (DOE). Effective operations and maintenance is one of the most cost-effective methods for reliability and efficiency (DOE).

What wastes energy in a building?

Energy and water losses from steam, water and air leaks, uninsulated lines, and maladjusted or inoperable controls are often considerable (DOE). Inadequate maintenance is a major cause of waste (DOE).

Related

Need a review of heating or cooling equipment in an older commercial building? Blume Mechanical Service (license CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment in Pinellas, Hillsborough and Pasco counties. Call 727-330-9131.

Sources: U.S. Department of Energy (DOE), Federal Energy Management Program — Commissioning in Federal Buildings (https://www.energy.gov/cmei/femp/commissioning-federal-buildings) · U.S. Department of Energy (DOE), Federal Energy Management Program — Operations and Maintenance in Federal Facilities (https://www.energy.gov/cmei/femp/operations-and-maintenance-federal-facilities)

Search Google for building recommissioning