HVAC, explained
Moisture control in homes: what EPA and DOE say
EPA says the key to mold control is moisture control (EPA). EPA says without adequate ventilation, moisture may build up indoors and mold may grow (EPA). EPA also says mold is frequently found on walls in cold corners behind furniture where condensation forms (EPA). A speaker in a DOE Building America webinar said the ventilation rate was based on controlling condensation in cold climates (DOE).
Moisture is the condition that mold needs, so controlling moisture is the main way to limit it. This page explains what the U.S. Environmental Protection Agency and the U.S. Department of Energy say about where indoor moisture comes from, how ventilation and fans help, and where moisture gets in. Each statement names its source, so you can check the wording against the original page.
What moisture control means
EPA says the key to mold control is moisture control (EPA). EPA also says mold can grow on virtually any organic material as long as moisture and oxygen are present (EPA).
The steps on this page focus on water and humidity, the conditions EPA's guidance names for mold growth. Each point below names the EPA or DOE source it comes from, so you can check the wording. Read each step as a check you can do at home or bring to a contractor.
Where indoor moisture comes from
EPA says cooking and showering can add to indoor humidity (EPA). EPA says humidity or dampness in the air can sometimes supply enough moisture for mold growth (EPA).
EPA says some moisture problems are not easy to see (EPA). Keep the list of places you checked with you when you call a contractor, so the visit covers each one. When a room smells damp, check the places you cannot see, such as the space behind a wall, and write down what you find.
Ventilation and exhaust fans
EPA says without adequate ventilation, moisture may build up indoors and mold may grow (EPA). EPA says bathroom and kitchen fans that exhaust to the outdoors also increase ventilation and help remove pollutants (EPA).
EPA says controlling moisture is the most effective way of keeping mold from growing in air ducts (EPA). Ask a contractor to check that each exhaust fan reaches the outdoors, and note any fan that is weak or noisy when you run it.
Condensation on cold surfaces
EPA says when warm, humid air contacts a cold surface, condensation may form (EPA). EPA says mold is frequently found on walls in cold corners behind furniture where condensation forms (EPA).
EPA says the heating and cooling system must be properly insulated to prevent condensation (EPA). Check that the ducts and pipes you can reach are insulated, and ask a contractor about any that are not. Write down each cold surface you find, with its location, so the next person who checks it has the list. Ask the contractor to show you where each one sits in relation to the living space.
Delayed maintenance and hidden damage
EPA says delayed or insufficient maintenance can lead to moisture problems in buildings (EPA). EPA says undiscovered or ignored moisture problems can create an environment in which mold can grow (EPA).
EPA also says a mold and moisture problem left unaddressed long enough can result in structural damage (EPA).
Crawl spaces, vapor barriers and ground water
EPA says moisture can pass from a crawl space into a building through cracks in walls, floors and ceilings (EPA). EPA says crawl spaces should be designed specifically to avoid moisture problems (EPA).
EPA says ground water may enter a crawl space where the water table is high and weather conditions are suitable (EPA). EPA says vapor barriers can keep damp or wet materials from drying quickly enough to prevent mold growth (EPA). Ask a licensed contractor to explain any vapor barrier, crawl space or drainage work before it starts, and to show you the drainage around the foundation.
Drying, measuring and the ventilation rate
EPA says to dry water-damaged areas and items within 24-48 hours to prevent mold growth (EPA). EPA says to use a moisture or humidity gauge to show whether the humidity in your home is at a good level (EPA).
EPA says low humidity may also discourage pests and dust mites (EPA). A speaker in a DOE Building America webinar said the ventilation rate was based on controlling condensation in cold climates (DOE). The same transcript says there was no requirement for controlling condensation in hot, humid climates (DOE).
Frequently asked
What is the key to controlling mold in a home?
EPA says the key to mold control is moisture control (EPA). EPA also says mold can grow on virtually any organic material as long as moisture and oxygen are present (EPA).
Do exhaust fans help with moisture?
EPA says bathroom and kitchen fans that exhaust to the outdoors also increase ventilation and help remove pollutants (EPA). EPA says without adequate ventilation, moisture may build up indoors and mold may grow (EPA).
Where does moisture collect in a house?
EPA says mold is frequently found on walls in cold corners behind furniture where condensation forms (EPA). EPA says moisture can pass from a crawl space into a building through cracks in walls, floors and ceilings (EPA).
How do I check the humidity in my home?
EPA says to use a moisture or humidity gauge to show whether the humidity in your home is at a good level (EPA). EPA says low humidity may also discourage pests and dust mites (EPA).
What should I do after water gets into a house?
EPA says to dry water-damaged areas and items within 24-48 hours to prevent mold growth (EPA). EPA says undiscovered or ignored moisture problems can create an environment in which mold can grow (EPA).
Does a crawl space need special design?
EPA says crawl spaces should be designed specifically to avoid moisture problems (EPA). EPA says ground water may enter a crawl space where the water table is high and weather conditions are suitable (EPA).
Related
- Bleach and biocides in mold cleanup: EPA guidance
- Heat advisory vs extreme heat warning in Tampa Bay
- Air sealing your home: where to start
Need an HVAC check on the ventilation or humidity in your Florida home? Blume Mechanical Service (CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment in Pinellas, Hillsborough and Pasco counties. Call 727-330-9131.
Sources: U.S. Environmental Protection Agency — Mold Course Chapter 2: (https://www.epa.gov/mold/mold-course-chapter-2) · U.S. Environmental Protection Agency — What are ten things I need to know about mold? (https://www.epa.gov/mold/what-are-ten-things-i-need-know-about-mold) · U.S. Environmental Protection Agency — Care for Your Air: A Guide to Indoor Air Quality (https://www.epa.gov/indoor-air-quality-iaq/care-your-air-guide-indoor-air-quality) · U.S. Department of Energy, Building America — Building America Webinar: Stump the Building Science Chump — Joe Lstiburek (Text Version) (https://www.energy.gov/cmei/buildings/building-america-webinar-stump-building-science-chump-joe-lstiburek-text-version)