Blume Mechanical ServiceBlumeMechanical Service

HVAC, explained

How to Reset a Furnace

Carrier describes a furnace reset as turning the furnace off at its power switch, waiting 30 seconds, and turning it back on, while Trane says a hard lockout needs a technician to reset the furnace (Carrier; Trane). Carrier says to turn the furnace power switch off, wait 30 seconds, and turn it back on, and to call for service if it trips again immediately (Carrier). Bryant says to turn off the power and wait "a few minutes" before resetting the thermostat and restarting the system (Bryant).

Bryant's guidance begins with four checks that cover the thermostat, the power, the filter, and whether vents and return grilles are open (Bryant). Carrier says a furnace that won't turn on may be caused by a tripped breaker, wrong thermostat settings, a dirty filter, or a power switch that is off (Carrier). Trane says newer gas furnaces have sensors and limit switches that signal the control board to shut off power and fuel when they detect a safety hazard (Trane).

What the makers say a reset involves

Carrier says the power switch is often mounted on the unit's side or a wall nearby, and it looks like a light switch (Carrier). Carrier's furnace-not-turning-on guide gives a wait of 30 seconds before the furnace is turned back on (Carrier). Carrier's ignitor guide says to call a professional if the unit still fails to light after a reset (Carrier). Bryant says to set the thermostat to heat, with the temperature above the room temperature, and to replace the batteries if the thermostat is battery-powered (Bryant).

What a lockout is

Trane says a lockout holds until the cause is addressed and the furnace is reset (Trane). Trane lists a dirty or defective flame sensor, a faulty ignitor, fuel pressure issues, a dirty filter, blocked vent pipes or flue, and a faulty control board as common causes of a lockout (Trane). Trane says a soft lockout covers the first one or two stops of the ignition sequence, and a third stop becomes a hard lockout (Trane). Carrier says dust and debris that block airflow can trigger safety switches that shut the furnace down to prevent overheating (Carrier). Bryant says a dirty flame sensor shuts the gas valve as a precaution when it is coated in carbon or dust (Bryant).

Repeated shutdowns and lockouts

Trane says a hard lockout needs a repair call so a technician can reset the furnace after the cause is fixed (Trane). Trane says that if the owner's manual addresses a lockout, it may suggest turning the power on, off, on and off twice within 30 seconds to see whether that resets the furnace (Trane). Bryant says a furnace that repeatedly starts and then shuts off needs a qualified technician to diagnose the cause (Bryant). Bryant says a limit switch should not be bypassed, and that repeated safety shutdowns require professional diagnosis (Bryant).

Safety lines before any reset

Carrier says that if you suspect a gas leak, "do not attempt to troubleshoot the furnace yourself" (Carrier). Carrier says to evacuate your home immediately if you smell rotten eggs or the carbon monoxide detector goes off, then contact emergency or utility services from a safe place (Carrier). Bryant says that if there is a gas smell, smoke, flames, or a suspected electrical hazard, "do not continue troubleshooting" (Bryant). Carrier says if other gas appliances stop too, the municipal gas supply may be interrupted, and the utility provider should be contacted immediately (Carrier). Bryant says "Never attempt to repair a gas valve yourself" (Bryant).

Checks to make before calling

Bryant says one-inch filters generally need monthly replacement, and wider filters may last longer between changes (Bryant). Bryant says to keep return grilles clear and confirm the supply registers are open (Bryant). Bryant says a clogged filter restricts airflow, which can make the heat exchanger overheat and set off a safety shutdown (Bryant). Trane says a homeowner should only change the air filter to try to resolve a hard lockout (Trane). Trane says filters generally need changing every 30 to 90 days, depending on filter quality, pets, and how often the furnace runs (Trane).

Gas and electrical work

Carrier recommends professional service for repairs on gas lines, electrical parts, and internal furnace parts, citing gas leaks, electrical hazards, and carbon monoxide risk (Carrier). Carrier says troubleshooting and diagnostic features vary by model, so the steps can depend on the Carrier model in the home (Carrier). Bryant says a code's meaning depends on the furnace model, so the owner's manual is the place to check it (Bryant). Bryant says the model number can be read from the rating-plate sticker inside the unit, which can help a service technician troubleshoot (Bryant).

Maintenance that lowers lockout risk

Trane says changing filters regularly is the easiest way to help avoid a lockout and many other furnace problems (Trane). Trane says a gas furnace's inner workings, venting system, and forced air parts need professional maintenance to run at peak efficiency, and it suggests a tune-up each fall (Trane). Trane says a homeowner can consider a maintenance plan with an HVAC company of their choosing, and that company will contact them when a maintenance call is due (Trane).

Airflow and safety switches

Bryant says blocked supply or return vents can limit airflow and add to overheating and lower system performance (Bryant). Bryant says the limit switch tracks internal furnace temperature and can cut burner operation when airflow is restricted or the blower fails (Bryant). Bryant says a blocked condensate drain can lead a float switch to stop the furnace from running, which helps prevent water damage (Bryant).

Frequently asked

How long should a furnace stay off during a reset?

Carrier's furnace-not-turning-on guide says to wait 30 seconds (Carrier). Bryant says to wait "a few minutes" after turning off the power (Bryant). Carrier's ignitor guide says to call a professional if the unit still fails to light after a reset (Carrier).

What is a hard lockout on a furnace?

Trane says a hard lockout happens when the controller stops the ignition sequence a third time, after one or two soft lockouts (Trane). Trane says it needs a repair call so a technician can reset the furnace after the cause is fixed (Trane).

Why won't my furnace stay on after a reset?

Carrier lists a dirty flame sensor as a possible cause, because it can shut the gas valve for safety (Carrier). Trane lists a dirty filter, blocked vent pipes or flue, and fuel pressure issues among common lockout causes (Trane).

What if the furnace keeps shutting off after a reset?

Carrier says to call for service if it trips again immediately (Carrier). Bryant says a furnace that repeatedly starts and then shuts off needs a qualified technician to diagnose the cause (Bryant).

Do I need to call a pro for this?

Maybe. Check the thermostat settings, the air filter, and whether vents and return grilles are clear first (Bryant). Bryant says to stop troubleshooting and contact a qualified service provider if these checks do not restore operation (Bryant). If the furnace trips again, repeatedly starts and shuts off, or shows a hard lockout, call a licensed contractor (Carrier; Bryant; Trane). Gas, electrical, and internal furnace repairs go to a licensed contractor, since Carrier cites gas leaks, electrical hazards, and carbon monoxide risk as reasons for professional service (Carrier).

Related

Questions about a specific system can go to Blume Mechanical Service at (727) 330-9131.

Sources: Carrier, Furnace Not Turning On? Troubleshooting & Repair Guide, https://www.carrier.com/us/en/residential/hvac-resources/furnaces/furnace-not-turning-on/ · Carrier, Furnace Ignitor: Understanding its Function and Importance, https://www.carrier.com/us/en/residential/hvac-resources/furnaces/furnace-ignitor/ · Bryant, Furnace Not Turning On? 12 Causes & How to Fix It, https://www.bryant.com/en/us/products/gas-furnaces/furnace-not-turning-on/ · Trane, Solving Furnace Hard Lock Out Issues, https://www.trane.com/residential/en/resources/troubleshooting/gas-furnaces/furnace-hard-lock-out/

Search Google for how to reset furnace