Blume Mechanical ServiceBlumeMechanical Service

HVAC, explained

How to Clean a Dehumidifier Properly

GE recommends regular cleaning to keep a dehumidifier working efficiently and properly (GE). GE's tank, older-model filter and grille procedures each start with switching the unit off and unplugging it (GE). For the tank, the next steps are to empty the water reservoir and wash it with dish soap and water; the grilles and case get dish soap and warm water (GE). GE gives one cleaning procedure each for the water tank and for the grilles and case, and separate air filter procedures for older and newer models (GE). ENERGY STAR says dust and dirt can clog the coils and grilles, and it recommends keeping the unit away from dust sources (ENERGY STAR).

A dehumidifier removes moisture from the air (ENERGY STAR). Its water tank, air filter, grilles and case are the parts GE describes cleaning (GE). GE gives different air filter intervals for older and newer models (GE).

Why regular cleaning matters

ENERGY STAR says that dust and dirt can clog the coils and grilles of a dehumidifier (ENERGY STAR). GE recommends cleaning on a regular basis so the unit keeps running efficiently and properly (GE).

Clean the water tank

Most portable dehumidifiers use a removable bucket with warning lights that show when it is full and needs emptying (ENERGY STAR). GE says to turn the unit off and unplug it first, then empty the water reservoir (GE). GE's wash step uses dish soap and water (GE). GE says the tank can be cleaned with a bleach solution of "90% water and 10% bleach" to prevent mildew (GE, read November 2026). Next, GE says to swish the bleach solution through the tank or bucket, then empty it and rinse with plain water (GE). Once it is clean, GE says to slide the tank back into place (GE).

Clean the air filter on older models

GE says to turn the unit off and unplug it before removing the filter (GE). GE says to pull the filter straight out by its handle (GE). GE also says never to run the dehumidifier with the filter out (GE). On HM50 and HM70 models, GE says to take out the bucket first, ease the filter down from below the front louvers, and then draw its bottom edge away from the unit (GE). GE says to vacuum the filter, and to wash it in warm, not hot, soapy water if it is very dirty (GE). GE's older-model filter steps say "DO NOT use any chemical cleaners." (GE). GE says to let the filter dry completely before putting it back (GE). Put it back by sliding the filter onto its tracks and pressing it inward (GE). GE says older models should have the filter checked every 2 to 3 weeks to see whether it needs cleaning (GE).

Clean the air filter on newer models

GE says the newer-model filter, found behind the rear grille, should get a check and a cleaning at least once every 250 hours of operation, and sooner if necessary (GE). On newer models, the Filter indicator light turns on once 250 hours have passed, as a prompt to clean the filter (GE). GE's newer-model steps are to take the filter out and clean it, then put it back and hold the filter button down for 3 seconds (GE). GE's steps also have you take off the rear grille, where the filter is attached (GE). The wash itself uses warm, soapy water, followed by a rinse and time to dry before the filter goes back (GE).

Clean the grilles and case

GE says to turn the unit off and unplug it before cleaning the grilles and case (GE). GE's guidance for the grilles and case is to wash them with dish soap in warm water (GE). GE also says "Do not use bleach or abrasive cleaners." (GE). Wipe the unit dry before plugging it back in (GE).

Keep the unit away from dust sources

ENERGY STAR advises placing the unit away from sources of dust and dirt, such as woodworking equipment, because these can clog the coils and grilles (ENERGY STAR). Most portable units have top-mounted discharge and can sit against a wall, but where a unit lacks it, ENERGY STAR says to keep it clear of walls and furniture so air can move freely around it (ENERGY STAR). ENERGY STAR says to keep doors and windows of the room closed while the unit runs, so the room is dried as efficiently as possible (ENERGY STAR). ENERGY STAR notes that removing moisture slightly warms the space around the unit, so air close to it can feel warmer than the rest of the room (ENERGY STAR). ENERGY STAR notes that cutting moisture sources can reduce how much dehumidification a home needs (ENERGY STAR). ENERGY STAR suggests that vent fans in bathrooms and kitchens can pull humidity out where it starts (ENERGY STAR). ENERGY STAR advises routing any drain hose clear of electrical cords and connections (ENERGY STAR). It also says water drainage or disposal should never be set up near electrical circuits or devices (ENERGY STAR). ENERGY STAR says to use a properly grounded outlet and to follow the manufacturer's warnings on electrical safety (ENERGY STAR).

What frost does

ENERGY STAR notes that if the room air falls below 65 degrees, frost can build up on the condensing coils (ENERGY STAR). That frost may hurt performance by making the compressor cycle on and off repeatedly without taking moisture out of the air (ENERGY STAR). If frost forms, ENERGY STAR advises turning the dehumidifier off and letting it thaw before switching it on again (ENERGY STAR). Some models have an anti-frost sensor that turns the unit off automatically when the air temperature falls below a set point (ENERGY STAR). For a space that typically falls below 65 degrees (F), ENERGY STAR says you may want to consider a model rated for lower temperatures (ENERGY STAR). If a room often gets cold, check the owner's manual for the temperature range the model is rated for.

When to get help

If the unit still will not run properly after cleaning, contact the manufacturer or a licensed professional. Check the model's owner's manual and nameplate first, and leave work inside the cabinet or near the electrical parts to them. Blume Mechanical Service (license CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment, and is brand-agnostic.

Frequently asked

How often should I clean a dehumidifier?

GE says older models should have the air filter checked every 2 to 3 weeks to see whether it needs cleaning (GE). For newer models, GE says the filter behind the rear grille should be looked at and cleaned no less often than every 250 hours of running time, and more often when necessary (GE).

Can I wash a dehumidifier water tank with bleach?

GE says a bleach solution of "90% water and 10% bleach" can be used on the tank to prevent mildew (GE, read November 2026).

Can I run the dehumidifier without the filter?

GE says not to run the dehumidifier without the filter installed (GE). GE says the filter should dry completely before it is reinstalled on older models (GE).

Does cleaning a dehumidifier affect its energy use?

GE says regular cleaning keeps a dehumidifier working efficiently and properly (GE). Neither the GE page nor the ENERGY STAR page gives a figure for how cleaning changes energy use.

Where should I put a dehumidifier?

ENERGY STAR advises placing the unit away from sources of dust and dirt, which can clog the coils and grilles (ENERGY STAR).

Should I clean the inside of the dehumidifier myself?

GE gives one cleaning procedure each for the tank, grilles and case, and separate air filter procedures for older and newer models (GE). For anything inside the cabinet, call a licensed professional.

Related

Want a licensed technician to look at the HVAC side of a moisture problem in Pinellas, Hillsborough or Pasco County? Blume Mechanical Service (license CAC-1822618) repairs, installs and maintains HVAC and refrigeration equipment, and is brand-agnostic. Call 727-330-9131.

Last updated: 2026-11-20

Sources: GE Appliances — Dehumidifier - Cleaning and Maintenance (https://products.geappliances.com/appliance/gea-support-search-content?contentId=34658) · ENERGY STAR — Dehumidifiers (https://www.energystar.gov/products/dehumidifiers)

Search Google for how to clean a dehumidifier