HVAC, explained
What a furnace flue pipe is and what makes it unsafe
A furnace flue pipe is the pipe that attaches to the furnace exhaust port and carries combustion byproducts out of the heat exchanger and to a termination point outside the home (Lennox). EPA says that if a flue is improperly sized, blocked, disconnected or leaking, it is a source of carbon monoxide (EPA).
EPA describes carbon monoxide as toxic, and says it "can kill you before you are aware it is in your home" (EPA). Lennox says a working alarm is needed to detect it, since it has no smell and no color (Lennox).
What the flue pipe does
Lennox says the flue pipe carries combustion byproducts, carbon monoxide among them, out of the home (Lennox). Lennox describes three ways the gases move: older natural draft systems rely on rising hot gases, induced draft furnaces pull them through with a combustion air inducer, and condensing furnaces push cooler exhaust out mechanically (Lennox). In every case, Lennox says, the pipe must pitch upward at least a quarter inch for each linear foot, running away from the furnace to the exit point (Lennox).
Pipe types and where each is used
Lennox says single-wall galvanized steel is only used for standard-efficiency furnaces (Lennox). Lennox says combustible material must be kept at least 6 inches from the outer surface of single-wall galvanized pipe (Lennox). B-vent has an insulating air pocket held between an aluminum inner layer and a galvanized steel outer one, and Lennox says the clearance from combustible materials drops to roughly 1 inch (Lennox). Lennox says B-vent is the preferred choice for mid-efficiency furnaces, especially where the pipe passes through walls or runs vertically (Lennox). Lennox says high-efficiency condensing furnaces produce exhaust between 100° and 150° F (Lennox). Lennox says PVC or CPVC is the correct material at those temperatures, and that the water vapor in that exhaust can corrode metal venting over time (Lennox).
What makes a flue pipe unsafe
EPA says that if a flue is improperly sized, blocked, disconnected or leaking, it is a source of carbon monoxide (EPA). EPA also lists back-drafting from furnaces as a source (EPA). Lennox names bird nests, debris, ice and snow packed around the termination cap as the most frequent blockages, and says even a partial blockage restricts the airflow the system needs to vent properly (Lennox). Lennox says corrosion, joints that have moved and blockages that push gases back can open routes for CO into the home (Lennox).
Corrosion, joints and venting errors
Lennox says single-wall galvanized pipe typically lasts 10 to 15 years, until moisture starts to damage it, and that once rust takes hold, small openings can let exhaust escape before it reaches the exterior vent (Lennox). Lennox says pipe connections are weakened by heat expansion, vibration and aging (Lennox). Lennox says a joint gap of one-sixteenth inch is enough to admit gas into the home (Lennox). Lennox also says a pipe of the wrong diameter, too little slope, or clearances outside specifications can produce poor draft and possible backdrafting (Lennox).
What CPSC tests found
CPSC ran a test program starting in 1999 on CO exposure from furnace vent pipes that are blocked or disconnected (CPSC). Its August 2000 report tested one draft hood equipped furnace, Furnace #1, in a test chamber (CPSC). With the vent pipe intact and not blocked, CO in the chamber was negligible, under 3 ppm (CPSC). With the vent blocked, readings were 1 ppm at the low end and more than 1000 ppm at the high end, depending on test conditions, and CO rose as the degree of blockage and the furnace on time increased (CPSC). With the vent disconnected, readings were 0 ppm at the low end and more than 1000 ppm at the high end, and were generally higher when the disconnect was outside the furnace closet (CPSC). The blocked-vent shutoff worked at first, but when the vent was totally blocked it did not turn the furnace off, and chamber CO ranged from 2 ppm to 331 ppm, varying with the test conditions (CPSC).
Signs of trouble and what to do
Lennox lists odd smells or fumes close to the furnace, rust stains, holes you can see, or sections that have separated, the furnace short-cycling and shutting off before its heating cycles finish, and a CO detector that goes off in any part of the home as signs of a damaged or unsafe pipe (Lennox). Lennox says "Do not wait on any of these." If the CO alarm goes off, Lennox says to leave immediately, call 911, and then contact a licensed HVAC technician once the household is safe (Lennox). EPA says that at higher concentrations CO can cause "flu-like symptoms that clear up after leaving home," and that exposure to CO at those levels can be fatal (EPA).
Inspection and repair
EPA says to have a trained professional inspect the central heating system, including furnaces, flues and chimneys, annually (EPA). CPSC urges an annual professional inspection of fuel-burning appliances, including furnaces, to detect deadly carbon monoxide leaks (EPA, quoting CPSC). CPSC recommends CO alarms in every home, on each level, in the area outside each sleeping area (EPA, quoting CPSC). Lennox says a CO detector is not a substitute for having the venting physically inspected by a professional (Lennox).
Owner checks between visits
Lennox says to test CO detectors monthly (Lennox). After winter weather, Lennox says to check the exterior termination point for ice or debris (Lennox). Lennox says severe corrosion, holes, or a leak confirmed at any point call for immediate replacement, not patching (Lennox). Lennox says a system 15 to 20 years old should have its flue checked even with no visible damage, because wear inside the pipe may not show (Lennox). Lennox says flue pipe repair or modification needs to be handled by a licensed HVAC technician (Lennox).
Codes and what the code summary says
DOE's Building America slides, Combustion Safety in the Codes, name the National Fuel Gas Code, International Fuel Gas Code and Uniform Plumbing Code (DOE). In that summary, appliance venting covers which materials are allowed, the vent type, sizing, installation and testing (DOE). The slides say safety codes become requirements when an authority having jurisdiction, meaning governments or fire safety authorities, adopts them (DOE). The slides also list vent sizing tables for atmospheric and fan-assisted (Category I) equipment among three key provisions (DOE). The slides mark the recommended inspection procedure for existing appliances as "Not a part of the code" (DOE), and list among its steps to "Inspect the vent for compliance to codes and deterioration" (DOE).
Frequently asked
What does a furnace flue pipe do?
It carries combustion byproducts from the furnace's heat exchanger to a termination point outside the home (Lennox).
What are the signs of a venting problem?
Lennox lists smells or fumes close to the furnace, rust, visible holes or sections that have come apart, a furnace that short-cycles, and a CO alarm that sounds in the house (Lennox). Lennox says "Do not wait on any of these" (Lennox).
Does a high-efficiency furnace use a different vent?
Lennox says high-efficiency condensing furnaces produce exhaust between 100° and 150° F, and PVC or CPVC is the correct vent material at those temperatures (Lennox).
Who should inspect or repair a flue pipe?
Lennox says a licensed HVAC technician handles any repair or modification to the pipe (Lennox), and EPA says to have a trained professional inspect the central heating system, including furnaces, flues and chimneys, annually (EPA).
Do I need to call a pro for this?
Yes. Flue pipe repair and changes go to a licensed contractor. EPA names a wrongly sized, blocked, disconnected or leaking flue as a source of carbon monoxide (EPA). Lennox says flue pipe repair or modification has to be handled by a licensed HVAC technician (Lennox).
Related
- Gas furnace maintenance: CO safety and yearly service
- Furnace heat exchanger cracks and carbon monoxide risk
- Vent-free (unvented) gas space heaters: air quality and carbon monoxide (CO) risk
- What a furnace limit switch is, and what happens when it trips
Questions about a specific system can go to Blume Mechanical Service at (727) 330-9131.
Sources: Lennox, What Is a Furnace Flue Pipe? Purpose, Types & Safety Tips (dated Sep 15, 2026), https://www.lennox.com/residential/lennox-life/consumer/furnace-flue-pipe · EPA, Carbon Monoxide's Impact on Indoor Air Quality (last updated July 15, 2026), https://www.epa.gov/indoor-air-quality-iaq/carbon-monoxides-impact-indoor-air-quality · CPSC, Furnace CO Emissions Under Normal and Compromised Vent Conditions (Furnace #1, draft hood equipped, August 2000), https://www.cpsc.gov/s3fs-public/pdfs/CO_emissions_furnace1.pdf · DOE Building America, Combustion Safety in the Codes (slides by Larry Brand, Gas Technology Institute, March 2012), https://www.energy.gov/sites/prod/files/2013/12/f6/combustion_safety_codes.pdf